|The Energy Plus Tap|
The Energy Plus Water Filter can be supplied with a tap or without a tap so you can use your own separate filter tap or a 3-way tap.
The Energy Plus has four cartridges, each of which plays a unique part in filtering and enriching your drinking water. They are:
1. A special ultra filtration membrane cartridge. This cartridge filters down to 0.1 micron and removes silt, rust, colloids, proteins, bacteria, viruses, pathogenic protozoa and cysts from the water. It is a physical barrier that does not use any chemicals.
2. The 2nd block filter absorbs a variety of organic and inorganic substances, chlorine and the more difficult to remove chloramine. Its dense pore structure and vast surface area is perfectly suited to improving taste and odour, colour, chemicals and fluoride.
Filter two is a proprietary matrix comprising at least two types of activated carbon, combined with proprietary Zeolite minerals, structurally bound with polymers into a highly porous block filter form.
Performance Data of Filter 2
• 1 Micron Nominal
• Chloramine reduction >99%
• Lead reduction >99%
• Chlorine reduction >99%
• Fluoride reduction 90%
• VOC - Volatile Organic Compounds >98%
• Metals – Aluminium, Iron, Mercury, Nickel & Zinc >98%
• MTBE reduction >97%
• Glyphosate reduction >99.9%
• Pharmaceutical compounds reduction >95%
• Nitrates reduction >92%
• Herbicides reduction >99%
3. The 3rd filter cartridge is composed of a combination of three different types of bioceramic natural mineral ball. These advanced bioceramics alkalise the water, change its Oxidation Reduction Potential, lend it antioxidant properties and improve the water structure. They also have an antibacterial effect, preventing the growth of harmful bacteria in the filter cartridge. Before the water enters this 3rd cartridge, it will have a slightly acidic pH (as do many water filter systems). The pH is typically raised to a pH level of 8.5 to 9.5, the ideal range for everyday drinking water.
4. The final-stage filter uses a combination of bioceramics to improve the structure of the water. These bioceramic minerals emit very low levels of subtle far infrared energy and help to improve water structure and absorbability. Suitable structured water with a negative Oxidation Reduction Potential supplies the body with beneficial negative ions. The water is finally polished by going through an additional stage with granulated activated carbon to remove any unpleasant taste or odour.
The exhaustive 4-stage process not only creates water that has undergone high levels of filtration, but also has good energy through the effect of the bioceramic media. The bioceramics also stimulate the release of active hydrogen.
The filters used in your Energy Plus Water Filter need to be replaced every year to ensure that they are functioning at peak efficiency, and to make sure the beneficial properties of the minerals do not wear out.
Fitting the Energy Plus Water Filter is a relatively simple job. Aside from cutting a hole in the rim of your sink or countertop for the tap, all you need to do is connect the existing feed pipe of your cold water tap, and then connect the pipework supplied from the filter to the drinking water tap, as per the diagram below:
Should you require more detailed instructions, simply click the 'Installation' tab above.
The Energy Plus Water Filter measures 40 x 40 x 15 cm. It fits easily under the sink without taking up too much space. No electrical connection is necessary. It comes complete with one of the drinking water taps shown.
You can order your Energy Plus Water Filter using the button below, or by calling us on 01764 662111. We'll also be more than happy to help should you require any further information in respect to fitting or installation.
Once the Energy Plus Water Filter System has been fitted underneath your sink (as per the instructions on the 'Installation' tab), its special water tap can be used in lieu of your normal tap when pouring water for:
In order to ensure the Energy Plus can properly alkalise, filter and enrich your water, you must take care to replace the filters on an annual basis by following these instructions:
Replacing the Filters in Your Energy Plus
The Energy Plus Water Filter has four cartridges. Cartridges require changing on an annual basis. To replace cartridges:
Replacement of Top Horizontal Post Filter 4
IMPORTANT: Before first use, run water through filter 10 minutes to prepare unit for use. Be sure to allow a minimum space of 50mm under the filter for removing the housing, to change the cartridge.
If you require further assistance please send us an email or call us on 01764 662 111.
The Energy Plus Water filtration system uses a number of different components to filter, clean and energize your water. These components include:
How to Install the Energy Plus Undersink Water Filter
Step 1: Choose location.
Position your filter in the cabinet nearest the cold water line, which is normally on the right side of your faucet, beneath the sink. Turn water off.
CAUTION: Water filter must be installed on cold water line only.
Step 2: Choose a faucet location.
The faucet may be installed into the hole normally used for your sink sprayer. If you have a sink sprayer installed and plan to use it, or you do not have an existing hole, you will have to drill a hole for the faucet.
If you are drilling a new hole, try to place it as near to the sink as possible – either on the metal lip if there is 40mm of clearance, or on the sideboard next to your sink if there is not.
The faucet will fit through a 12mm hole or larger. For drilling through a metal sink, first make a small indentation with a punch where you want to install the faucet. (CAUTION: WEAR EYE PROTECTION WHEN DRILLING.)
Step 3: Insert faucet.
Remove the hardware from the faucet stem for later use, then slide the large chrome plated washer onto the stem, followed by the large rubber washer. Place the faucet stem through the hole in the rubber washer. Slide the large metal washer and nut onto the faucet stem. Tighten the nut to secure the faucet in place.
Step 4: Install water supply connector/selftapping valve.
Note: Always check the local plumbing codes before tapping into a water line.
WARNING: WATER SUPPLY PRESSURE MUST NOT EXCEED 100 PSI. Failure to set correct pressure could result in leakage/bursting of unit.
a. Assemble saddle-tapping valve on tube. Hold back plate and saddle valve against tubing in a position directly each other. Tighten screw enough so that the saddle valve and back plate are held securely against tubing.
b. Connect source water feed tubing to valve body using compression fitting. Slide nut and sleeve onto tubing (in that order). Install plastic tubing insert into white tubing. Install tube with insert and sleeve into valve body. Thread compression nut onto valve body. Tighten. Turn saddle-tapping valve handle clockwise until it is firmly seated and piercing lance is fully extended.
c. Attach tubing between the outlet connection of the filter and the faucet tap. Unscrew compression nut from outlet fitting. Remove red cap. Slide compression nut of outlet fitting over tubing and push tubing through until tube stop. Tighten compression nut onto connection fitting.
CAUTION: Do not open valve until system is activated. Turn on cold water supply.
Check saddle-tapping valve installation for leaks.
Step 5: Connect tubing.
Connect tubing from cold water line (water supply line) to the inlet of the water filter. Allow enough slack in the tubing so the unit can be easily removed for filter cartridge. Measure and cut the end of tubing square.
1. Unscrew compression nut counter clockwise from connection fitting.
2. Screw male threads of quick connect fitting into the inlet threads of water filter.
3. Slide compression nut onto the end of tubing. Push tubing through to the tube stop inside quick connect fitting.
4. Screw compression nut onto quick connect fitting. Tighten securely. Do not crossthread. The system is now connected.
Step 6: Test the system
Open the new tap and turn on the mains feed slowly. Check that there are no leaks in the connecting pipework, or at the filter cartridge connections.
If any leaks are present, immediately turn off the mains feed and double check all connections.
If you require further assistance with the fitting of your Energy Plus Water Filter, please email or call us on 01764 662 111.
At Water for Health we want prospective clients to buy from us with confidence. Our mission is to make a difference in the quality of life of as many people we can. We have very many customers who tell us we have made a difference to them and this inspires us to continue to do what we do. To underpin our commitment we offer the following 7 point guarantee.
We always endeavour to treat our clients and prospective clients respectfully. We constantly strive to offer a caring attitude and a knowledgeable service. Our approach is to treat others in the way we would like to be treated ourselves. We are available at the end of the phone or by email to discuss with you your requirements and concerns with a high degree of product expertise, confidentiality and professionalism. We can be reached by phone Monday to Friday between 8.45am and 5.30pm on 01764 662111.
We want all our clients to be happy with any product they buy from us. If however you purchase a product that does not meet your expectations, then we will refund your purchase cost at any time within 3 months if you are unhappy with it. It is your responsibility to notify us by phone or email first then send the product or remaining product and or packaging to our UK address. We will process your money back promptly (that’s all the small print!).
With the equipment we supply we warrant that the product will remain in working order for the life of the guarantee. In the unlikely event that your product malfunctions within the guarantee timeframe we'll replace it with the same model, or discuss an alternative with you if it is no longer available.
If it is a food product or dietary supplement you buy, the results can be varied depending on a wide variety of factors. The benefit will vary from person to person as can the period before benefit is felt. We endeavour to source quality products from suppliers who have a similar ethos to ourselves. Should you wish to know which product might be most suitable for you please feel to call or email us as we are always happy to help. Please note we do not offer medical advice but are always pleased to point clients in the direction of resources that may be of value.
At Water for Health we aim to dispatch your order within 48 hours of receipt. This is often done the same day subject to the product being in stock. However Water for Health import products from all over the world and there could be times where we might briefly be out of stock with a product due to timescales from ordering to delivery. Should the item be out of stock we will notify you within one working day to provide a delivery date. If you have a special delivery requirement then please call us on 01764 662111 prior to placing your order and we will do our best to assist. You can read more about our estimated delivery timescales here.
With an increasing threat of identity theft, we realise that security is of paramount importance. Be assured that your safety is protected with state-of-the-art Secure Socket Layer (SSL) technology that encrypts sensitive information on both your browser and our server. You’ll know that the checkout process is secure when you see an ‘s’ following the normal ‘http’ designation in the URL address bar. All payments are processed through Sagepay who are the UK’s biggest payment gateway and renowned for there security.
We are continually trying to source and develop new lines of products which can make a difference to the lives of our customers. We believe the products we sell are some of the best on the market. We are selective in the brands which we stock. We look for products that use high quality ingredients and we against the use of fillers, herbicides, pesticides and artificial colourings and flavourings to name but a few. These values are not only important to us but also to our suppliers.
We understand the wealth of information and mis-information available on the subject of health. This is something we try to cut through ourselves to be able to offer a knowledgeable service to our clients. We believe in the importance of being informed. As Water for Health is striving to provide products to improve the quality of life of its customers the following quote by Albert Einstein is very fitting: “We believe that an informed citizenry will act for life and not for death.” To be able to do this we send an optional newsletter, write articles and provide other information to our customers through our blog here and other articles which can be accessed here.